Greetings from Maryland
-
- Just Starting Out
- Posts: 5
- Joined: Fri Mar 23, 2018 6:00 pm
- Boat Name: No Boat Yet
Greetings from Maryland
Hello Everyone,
I have long held an interest in steam power plants. I also write for a few naval history websites.
I recently have been researching information for a piece on triple expansion engines and turbines. Eventually, I would like to construct models of each to collect data.
I decided to join this forum to learn from those with experience. Unfortunately, I cannot contribute much knowledge, but I hope everyone here would be kind enough to share what they know.
I have long held an interest in steam power plants. I also write for a few naval history websites.
I recently have been researching information for a piece on triple expansion engines and turbines. Eventually, I would like to construct models of each to collect data.
I decided to join this forum to learn from those with experience. Unfortunately, I cannot contribute much knowledge, but I hope everyone here would be kind enough to share what they know.
- TahoeSteam
- Full Steam Ahead
- Posts: 813
- Joined: Fri Mar 07, 2014 5:38 am
- Boat Name: Wayward Belle
- Location: South Lake Tahoe, CA, USA
- Contact:
Re: Greetings from Maryland
Welcome to the forum. There are decades (if not centuries) of collective hands-on experience here and many whom are willing to help. What are the aims of your writings?
~Wesley Harcourt~
https://www.youtube.com/c/wesleyharcourtsteamandmore
https://www.youtube.com/c/wesleyharcourtsteamandmore
- Kelly Anderson
- Full Steam Ahead
- Posts: 173
- Joined: Fri Feb 11, 2011 1:28 am
- Boat Name: Vividus
- Location: Strasburg, PA
- Contact:
Re: Greetings from Maryland
What piece are you after?Navy General Board wrote:I recently have been researching information for a piece on triple expansion engines and turbines.
It was not easy to convince Allnutt. All his shop training had given him a profound prejudice against inexact work, experimental work, hit-or-miss work.
-
- Just Starting Out
- Posts: 5
- Joined: Fri Mar 23, 2018 6:00 pm
- Boat Name: No Boat Yet
Re: Greetings from Maryland
Right now I am collecting data.Kelly Anderson wrote:What piece are you after?Navy General Board wrote:I recently have been researching information for a piece on triple expansion engines and turbines.
I am searching for more first hand experience. Find use who have utilized such engines and get their first hand accounts on the operation of those engines. Any quirks, issues with maintenance, etc.
Once a few other projects are out of the way and time willing, maybe build a test mule to collect additional data
- cyberbadger
- Full Steam Ahead
- Posts: 1123
- Joined: Thu Nov 07, 2013 9:16 pm
- Boat Name: SL Nyitra
- Location: Northeast Ohio, USA
Re: Greetings from Maryland
There is a general recognized concept that somewhere say around 2000 Horsepower steam turbines start to make more sense then reciprocating steam engines.Navy General Board wrote:Kelly Anderson wrote:Navy General Board wrote:Find use who have utilized such engines and get their first hand accounts on the operation of those engines. Any quirks, issues with maintenance, etc.
If you look at the Steam Boating Association of Great Britian (SBA), which has the largest membership of steamboaters world wide, they have a boat Register with an advanced search capability.
If you search by engine type - I can't even find an example of steam turbine powered steamboat.
Small turbines are loud, hard to come by, inefficient(at this scale), and not terribly powerful(at this scale).
Almost any turbine that would be appropriate would just do very poorly compared to pretty much any reciprocating steam engine. A 1-10 horsepower reciprocating steam engine is the norm for a steamboat up to 40ft in length.
Poke around the SBA's register and take a look at the Advanced Search...
http://www.steamboatassociation.co.uk/page-1117882
Hey - but if want to make a small turbine steamer go for it! I'm sure it can be done, just not common for several very good reasons.
Welcome to the forum.
-CB
-
- Full Steam Ahead
- Posts: 179
- Joined: Sun Jun 05, 2011 7:08 am
- Boat Name: Blue Buccaneer
- Location: Wallasey
Re: Greetings from Maryland
Hi
www.ss-shieldhall.co.uk
Shieldhall must be the largest steamer on our books at 268 feet long and build quite late 1955 and even she has Up and Downers rather than turbines
Mike
www.ss-shieldhall.co.uk
Shieldhall must be the largest steamer on our books at 268 feet long and build quite late 1955 and even she has Up and Downers rather than turbines
Mike
Mike Cole
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Greetings from Maryland
Here is a small steam turbine with 4" diameter rotor assembly (it has three rotors) my buddy is working on and I've been working with him on it. Sorry about the video quality (cell phone).
This is on 80 psi air and there will be another reduction shaft for final drive. This is very easy to build with a lathe and drill press. No fancy 4D machining involved. Uses 3/8" timing belts and pulleys.
The sound speaks for itself
-Ron
This is on 80 psi air and there will be another reduction shaft for final drive. This is very easy to build with a lathe and drill press. No fancy 4D machining involved. Uses 3/8" timing belts and pulleys.
The sound speaks for itself
-Ron
-
- Just Starting Out
- Posts: 5
- Joined: Fri Mar 23, 2018 6:00 pm
- Boat Name: No Boat Yet
Re: Greetings from Maryland
Much appreciated for the info. I will certainly go there to gather info.cyberbadger wrote: There is a general recognized concept that somewhere say around 2000 Horsepower steam turbines start to make more sense then reciprocating steam engines.
If you look at the Steam Boating Association of Great Britian (SBA), which has the largest membership of steamboaters world wide, they have a boat Register with an advanced search capability.
If you search by engine type - I can't even find an example of steam turbine powered steamboat.
Small turbines are loud, hard to come by, inefficient(at this scale), and not terribly powerful(at this scale).
Almost any turbine that would be appropriate would just do very poorly compared to pretty much any reciprocating steam engine. A 1-10 horsepower reciprocating steam engine is the norm for a steamboat up to 40ft in length.
Poke around the SBA's register and take a look at the Advanced Search...
http://www.steamboatassociation.co.uk/page-1117882
Hey - but if want to make a small turbine steamer go for it! I'm sure it can be done, just not common for several very good reasons.
Welcome to the forum.
-CB
By built comparison engines, I mean build a boiler and the powerplants. I'd like to be able to swap one engine out for the other on the same boiler. I am really after the figures on horse power, fuel consumption, and the like.
Haven't really thought of building a model to test on the water, but that might be something for a little further down the road.
-
- Just Starting Out
- Posts: 5
- Joined: Fri Mar 23, 2018 6:00 pm
- Boat Name: No Boat Yet
Re: Greetings from Maryland
Thank you for the tip. I just reached out to them.Mike Cole wrote:Hi
http://www.ss-shieldhall.co.uk
Shieldhall must be the largest steamer on our books at 268 feet long and build quite late 1955 and even she has Up and Downers rather than turbines
Mike
-
- Just Starting Out
- Posts: 5
- Joined: Fri Mar 23, 2018 6:00 pm
- Boat Name: No Boat Yet
Re: Greetings from Maryland
[quote="DetroiTug"]Here is a small steam turbine with 4" diameter rotor assembly (it has three rotors) my buddy is working on and I've been working with him on it. Sorry about the video quality (cell phone).
This is on 80 psi air and there will be another reduction shaft for final drive. This is very easy to build with a lathe and drill press. No fancy 4D machining involved. Uses 3/8" timing belts and pulleys.
The sound speaks for itself
-Ron
Good stuff. That is about the size of the model I would need. Just large enough to be able to connect my instruments to. The simplicity really appeals to me.
This is on 80 psi air and there will be another reduction shaft for final drive. This is very easy to build with a lathe and drill press. No fancy 4D machining involved. Uses 3/8" timing belts and pulleys.
The sound speaks for itself
-Ron
Good stuff. That is about the size of the model I would need. Just large enough to be able to connect my instruments to. The simplicity really appeals to me.