Steam Actuated Inlet Valves?
-
- Full Steam Ahead
- Posts: 134
- Joined: Mon Oct 31, 2016 5:57 pm
- Boat Name: No Boat Yet
- Location: Yukon, OK
Steam Actuated Inlet Valves?
Would it be possible to actuate the opening and closing of valves directly by using steam?
Essentially, I'm thinking of a situation where a small amount of steam could be admitted to a small cylinder via a small solenoid. This steam would then force itself against the piston, which is attached to the main valvegear (presumably poppet), thereby opening the valve against the pressure of the steam and admitting steam into the much larger main engine cylinder.
It seems like this would be a good way to electronically control an engine while at the same time allowing very fast valve actuation, without the issues inherent in using much larger solenoids to control the admission directly. Presumably, because the advantages are mostly for the intake valve this would be best suited for a uniflow application.
I've done some research and so far I haven't been able to find any information about this having been tried in the past, although I'm sure I'm not the first person with this idea.
Essentially, I'm thinking of a situation where a small amount of steam could be admitted to a small cylinder via a small solenoid. This steam would then force itself against the piston, which is attached to the main valvegear (presumably poppet), thereby opening the valve against the pressure of the steam and admitting steam into the much larger main engine cylinder.
It seems like this would be a good way to electronically control an engine while at the same time allowing very fast valve actuation, without the issues inherent in using much larger solenoids to control the admission directly. Presumably, because the advantages are mostly for the intake valve this would be best suited for a uniflow application.
I've done some research and so far I haven't been able to find any information about this having been tried in the past, although I'm sure I'm not the first person with this idea.
-
- Full Steam Ahead
- Posts: 149
- Joined: Fri May 13, 2016 2:42 am
- Boat Name: Alphington
- Location: Da Nang City Vietnam
Re: Steam Actuated Inlet Valves?
There are IC engines that use high pressure air or gas to open poppet valves using cylinders that are controlled with an engine management system. Trying to do this with steam could be done but it would make for a very elaborate system. Firstly the operating gas or steam needs to be up to pressure before the engine can be started. If using steam the plumbing for valve control system would need to be organized such the the steam is continually exhausted from every corner of the system to remove condensate and avoid hydraulic lock. If the valve control system fails while the engine is running at full speed it could lead to a major failure of the engine. The engine valve control cylinders need to be actuated by electronically controlled pilot valves which are generally quite small and so very high pressure compressed gas is usually used, 1000PSI or higher. Probably not the boiler pressure that you would like to run.
It would be far easier to use very large solenoids to directly open and/or close the inlet valves. In this case very short stroke balanced poppet valves would probably be the best candidate.
Lionel
It would be far easier to use very large solenoids to directly open and/or close the inlet valves. In this case very short stroke balanced poppet valves would probably be the best candidate.
Lionel
- dampfspieler
- Full Steam Ahead
- Posts: 254
- Joined: Wed Nov 18, 2009 6:59 am
- Boat Name: No Boat Yet
- Location: Neubrandenburg, Germany
- Contact:
Re: Steam Actuated Inlet Valves?
Hi tom,
If you are interested in variable valve-timing look for "Knaggen-Ventilsteuerung".
Some interesting tweets you can find here (in german):
- Zwillings-Tandem-Verbundfördermaschine Zeche Radbod, Hamm
- Dampffördermaschine bauen
Such a system was also used by SENTINEL in their steam shunting locos.
Regards Dietrich
a steam engine is a very tolerant system - it runs even with very poorly set valves. But the solution had to be simple - yours is difficult. Valves had to operated by incompressible media like steel .I've done some research and so far I haven't been able to find any information about this having been tried in the past, although I'm sure I'm not the first person with this idea.
If you are interested in variable valve-timing look for "Knaggen-Ventilsteuerung".
Some interesting tweets you can find here (in german):
- Zwillings-Tandem-Verbundfördermaschine Zeche Radbod, Hamm
- Dampffördermaschine bauen
Such a system was also used by SENTINEL in their steam shunting locos.
Regards Dietrich
-
- Full Steam Ahead
- Posts: 246
- Joined: Mon Dec 14, 2015 2:12 pm
- Boat Name: Platypus, Shelduck
- Location: Very eastern England
Re: Steam Actuated Inlet Valves?
Some "Southworth" style pumps have master-slave valve gear, where a mechanical linkage operate a pilot valve and steam pressure then shuttles the main steam valve. In this application the arrangement is mostly so that the pump never hangs between up and down strokes, and Southworth pumps are usually sized to run very slowly - strokes per minute very often - much slower than most steam engines producing power via a shaft.
All the same, the arrangement is similar in some ways to having a master-slave solenoid and steam shuttle valve.
All the same, the arrangement is similar in some ways to having a master-slave solenoid and steam shuttle valve.
- Lopez Mike
- Full Steam Ahead
- Posts: 1903
- Joined: Wed Dec 07, 2011 6:41 am
- Boat Name: S.L. Spiffy
- Location: Lopez Island, Washington State, USA
Re: Steam Actuated Inlet Valves?
And why would anyone want to share a launch with such an engine? You might as well inject a light oil into the cylinder and let the heat of compression ignite it. Dispense with the heavy and wasteful boiler. It is a very well developed technology, poppet valves and all. Horrid too.
If you think you are too small to make a difference, try sleeping with a mosquito.
Dalai Lama
Dalai Lama
-
- Full Steam Ahead
- Posts: 186
- Joined: Sun Sep 02, 2012 2:39 pm
- Boat Name: No Boat Yet
- Location: Cathlamet, WA
Re: Steam Actuated Inlet Valves?
My experience on a Fletcher Class destroyer with Worthington vertical pumps, that had free piston main valves, was often one of frustration. Not if, but when the main valve hung-up the only way to restore operation was to whack it with a 4lb hammer since there wasn't external means to move the valve.In this application the arrangement is mostly so that the pump never hangs between up and down strokes,
Dave
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Steam Actuated Inlet Valves?
Quote: "Would it be possible to actuate the opening and closing of valves directly by using steam?"
To effect any sort of precise motion, a gas is a very poor medium in which to accomplish this, it normally involves closed loop systems with linear encoder feedback. Especially a gas that has to be kept above a relatively high temperature lest it implode on itself .
Electromagnets (solenoid coils) use a lot of current which is a negative to shaft horsepower on a self contained plant.
-Ron
To effect any sort of precise motion, a gas is a very poor medium in which to accomplish this, it normally involves closed loop systems with linear encoder feedback. Especially a gas that has to be kept above a relatively high temperature lest it implode on itself .
Electromagnets (solenoid coils) use a lot of current which is a negative to shaft horsepower on a self contained plant.
-Ron
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Steam Actuated Inlet Valves?
Quote: "My experience on a Fletcher Class destroyer with Worthington vertical pumps, that had free piston main valves, was often one of frustration. Not if, but when the main valve hung-up the only way to restore operation was to whack it with a 4lb hammer since there wasn't external means to move the valve."
I've never had that issue with the Southworth steam pump, not once ever has the shuttle piston stuck. It's a very close fit and Of course I do have an oiler on it.
-Ron
I've never had that issue with the Southworth steam pump, not once ever has the shuttle piston stuck. It's a very close fit and Of course I do have an oiler on it.
-Ron
- Attachments
-
- IMG_3296 (Medium).JPG (65.88 KiB) Viewed 7322 times
-
- IMG_3158 (Medium).JPG (83.93 KiB) Viewed 7322 times
- marinesteam
- Full Steam Ahead
- Posts: 309
- Joined: Thu Nov 19, 2009 2:51 am
- Boat Name: TBD
- Location: Colorado USA
Re: Steam Actuated Inlet Valves?
Yes it would, they already exist. Google Steam piloted piston solenoid valve.
Not sure what you mean by very fast. The speed will usually be determined by the shuttle time of the solenoid and the pressure differential in the valve.
Ken
Not sure what you mean by very fast. The speed will usually be determined by the shuttle time of the solenoid and the pressure differential in the valve.
Ken
TriangleTom wrote:Would it be possible to actuate the opening and closing of valves directly by using steam?
Essentially, I'm thinking of a situation where a small amount of steam could be admitted to a small cylinder via a small solenoid. This steam would then force itself against the piston, which is attached to the main valvegear (presumably poppet), thereby opening the valve against the pressure of the steam and admitting steam into the much larger main engine cylinder.
It seems like this would be a good way to electronically control an engine while at the same time allowing very fast valve actuation, without the issues inherent in using much larger solenoids to control the admission directly. Presumably, because the advantages are mostly for the intake valve this would be best suited for a uniflow application.
I've done some research and so far I haven't been able to find any information about this having been tried in the past, although I'm sure I'm not the first person with this idea.
- DetroiTug
- Full Steam Ahead
- Posts: 1863
- Joined: Fri Nov 27, 2009 5:56 pm
- Boat Name: Iron Chief
- Location: Northwest Detroit
Re: Steam Actuated Inlet Valves?
This subject comes up quite often in the experimental steam car community and electronic valves on a steam engine is often sought after but always abandoned. Run in to too many issues cycling a solenoid thousands of times per minute, even a few hundred is problematic.
-Ron
-Ron