The Steamboating Forum

A Forum for the discussion of Steam Boats
It is currently Mon Nov 20, 2017 3:23 pm

All times are UTC




Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Alphington Steam launch
PostPosted: Fri Nov 03, 2017 4:42 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
Hi, I started off introducing the build of my modified Stuart 6A in the welcome section but I have decided to start again here and work through the build of the engine and then though that of my launch build which is about to start.

I modeled the entire modified 6A in Solidworks before starting any machining.

Image

Further CAD images here:

https://www.facebook.com/pg/steam.launch/photos/?tab=album&album_id=1892140141114538

Here is a link to the Lubricator for my 6A. The lubricator design is loosely based on a design by Alex Ritchie that uses Interlube mini pumps, but is a total rework. My lubricator has a two compartment tank enabling the use of cylinder oil and bearing oil within the one unit. One pump is used for cylinder oil and nine pumps are used for main, big end, little end, and cross head bearings.

There are many pictures of my engine build on my Facebook page and can be found in the Albums, I have had too spread the build across a number of albums because loading gets to slow using a single album. please see the link below for the lubricator album. I will be continually adding to the 6A build albums, the engine is almost finished and I have hundreds of photos of the build.

https://www.facebook.com/pg/steam.launch/photos/?tab=album&album_id=1892075684454317

Image

cheers

Lionel


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Mon Nov 06, 2017 3:04 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
Here are some pictures of making the valve gear from the reversing lever through to the Stevenson's links

Image

Many more pictures here

https://www.facebook.com/pg/steam.launch/photos/?tab=album&album_id=1893141781014374


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Mon Nov 06, 2017 7:23 am 
Offline
Lighting the Boiler
Lighting the Boiler
User avatar

Joined: Wed Nov 18, 2009 6:59 am
Posts: 33
Location: Neubrandenburg, Germany
Boat Name: No Boat Yet
Hello Lionel,

very nice work. Why have you built the dies from hardened steel and not from bronze?

I have built the die at my steam engine from IGLIDUR H1.

Image

Best Dietrich


Last edited by dampfspieler on Mon Nov 06, 2017 11:56 am, edited 1 time in total.

Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Mon Nov 06, 2017 11:00 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
The only important thing between two bearing surfaces is that one is harder that the other, in my case the Stevenson's link is hardness 40HRC and the Dies are 60HRC.


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Wed Nov 08, 2017 6:20 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
Hi, a few pictures of the balanced slide valves and rods

Image

Many more pictures here

https://www.facebook.com/pg/steam.launch/photos/?tab=album&album_id=1894542014207684

Cheers

Lionel


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Wed Nov 08, 2017 12:26 pm 
Offline
Full Steam Ahead
Full Steam Ahead
User avatar

Joined: Fri Nov 27, 2009 5:56 pm
Posts: 1423
Location: Northwest Detroit
Boat Name: Iron Chief
Lionel

Very nice work!

Really gives me the bug to build another engine, but I'm bogged down in a big steam project now.

-Ron


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Wed Nov 08, 2017 5:47 pm 
Offline
Full Steam Ahead
Full Steam Ahead
User avatar

Joined: Fri Nov 20, 2009 5:34 am
Posts: 1432
Location: Phila PA USA
Boat Name: Margaret S.
Very nice job you are doing on this build!

"The only important thing between two bearing surfaces is that one is harder that the other."

It is also necessary to not exceed the maximum allowable bearing pressure between the surfaces, various allowable bearing pressures according to materials and service conditions are very important. Many engineering handbooks give this data according to material combinations and surface speeds, etc.


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Thu Nov 09, 2017 3:10 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
Thank you I am trying to make the best job of it that I can.

Yes, Fredrosse, you are quite correct, my answer regarding the bearing materials was rather simplistic, I should have said " for this application" where the the materials I have selected are far more than adequate, and, I have increased the bearing surface area of the die to double that specified on Stuarts original drawings, effectively halving the pressure. In the case of the die running on the Stevenson's link, the velocity of the sliding part is extremely low. Many people use bronze for the die, they also radius the leading edges of the die. This creates a situation where any dirt and grit that lands on the Stevenson's link with become embedded in the die and the die will be transformed into a lapping block that will soon wear away the Stevenson's link. My Hardened die will not pick up the grit, and I have been careful to not radius the leading edges of the die. Bronze bearings are great, just so long as you keep pumping oil in to stop the entry of dirt.


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Sun Nov 12, 2017 10:22 am 
Offline
Lighting the Boiler
Lighting the Boiler

Joined: Fri May 13, 2016 2:42 am
Posts: 32
Location: Da Nang City Vietnam
Boat Name: Under Construction
Here are some drain valves that I made for my 6A

Image

Image

All of the machining pictures are here:

https://www.facebook.com/pg/steam.launch/photos/?tab=album&album_id=1896634957331723


Top
 Profile  
Reply with quote  
 Post subject: Re: Alphington Steam launch
PostPosted: Sun Nov 19, 2017 5:15 pm 
Online
Full Steam Ahead
Full Steam Ahead
User avatar

Joined: Fri Mar 07, 2014 5:38 am
Posts: 423
Location: South Lake Tahoe, CA, USA
Boat Name: Wayward Belle
Lionel,

The work you're doing is absolutely beautiful. I have the utmost respect for your machining ability, and your desire to make every single bit, including hardware, yourself. Hats off to you.

Question:
Do you have good patternmakers and foundries there that can make intricate iron and bronze castings?

_________________
~Wesley Harcourt~
Check out the steamboat videos on my YouTube page: https://www.youtube.com/c/wesleyharcourtsteamandmore


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ]  Go to page 1, 2  Next

All times are UTC


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group