Welcome!

Read this first then introduce yourself here.
Post Reply
vixit1862
Just Starting Out
Just Starting Out
Posts: 3
Joined: Mon Nov 07, 2016 7:56 pm
Boat Name: No Boat Yet

Welcome!

Post by vixit1862 » Tue Nov 08, 2016 1:44 pm

Good Day everyone. I am a new member of both this forum and the SBA. The reason for my sudden interest in Steam boat forums etc, is that I am trying to buy a small steam boat. Unfortunately, the current owner does not have any papers. The boat is in France, and the owner is French. So I shall attempt to upload a few photos, and hope that someone can identify the boiler and engine so that I can do some technical rerearch on them.ImageImageImage
I do hope there are a few pics there.
Anyone lnow anything about this boiler and/or the engine
Thank you.
Mike Rometer
Full Steam Ahead
Full Steam Ahead
Posts: 936
Joined: Sat Aug 13, 2011 6:41 pm
Boat Name: B.N.Y.S.
Location: Middle Earth

Re: Welcome!

Post by Mike Rometer » Tue Nov 08, 2016 5:36 pm

Firstly welcome.

Secondly, have you looked for the name in the SBA register? It's surprsing how many boats are there, even if the owners details haven't been kept up to date. Obviously, check previous incarnations of the same craft as well.

After that, check out Radhew's site, he has a load more, particularly Continental ones.

Unfortunately he hasn't been posting on here much lately, but then he is a busy boy. :)

The engine looks quite S.T. 6a.
Retirement is about doing what floats your boat!

A BODGE : - A Bit Of Damn Good Engineering.
User avatar
Akitene
Warming the Engine
Warming the Engine
Posts: 81
Joined: Wed Nov 18, 2009 7:39 pm
Boat Name: No Boat Yet
Location: Bordeaux, France

Re: Welcome!

Post by Akitene » Tue Nov 08, 2016 7:01 pm

Welcome aboard, vixit1862.

Interesting story. There are very few steamboats in France (less than 20 that I know of); I can't pretend to know every French steamboat but the pics of this one don't ring a bell. I'm not very surprised about the lack of paper - BTW, you mean a boiler certificate?

The engine looks like a Stuart 6A but the cylinder covers and the steam chest cover don't match (or they have been modified).

I'd like to see better pics of your soon-to-be steamboat.

Regards.
User avatar
TahoeSteam
Full Steam Ahead
Full Steam Ahead
Posts: 813
Joined: Fri Mar 07, 2014 5:38 am
Boat Name: Wayward Belle
Location: South Lake Tahoe, CA, USA
Contact:

Re: Welcome!

Post by TahoeSteam » Wed Nov 09, 2016 5:08 am

Welcome to the forum!

The columns don't match a Stuart 6 either.. Stuarts have cast back standards and turned front columns. Any chance of getting the engine's internal dimentsions (bore+stroke)? That may help in determining it's pedigry. Sometimes people take castings from one make and throw them together with castings from another or something of their own creation altogether.

The boiler, is it a vertical firetube, a vertical watertube, or a combination of the two?

Here's a link to Rainer Radow's registry, searchable with engine type, boiler, etc;

http://www.steamboating.de/steamboat/st ... -radow.php
User avatar
TahoeSteam
Full Steam Ahead
Full Steam Ahead
Posts: 813
Joined: Fri Mar 07, 2014 5:38 am
Boat Name: Wayward Belle
Location: South Lake Tahoe, CA, USA
Contact:

Re: Welcome!

Post by TahoeSteam » Wed Nov 09, 2016 5:15 am

Some quick perusing of Rainer's amazing registry produced this launch that has the same engine:

http://www.steamboating.de/steamboat/st ... ect=engine

It appears the engine is an Anthony Beaver Compound 2" & 3-1/4" x 2" or in those funny mili-whatevers; 50.8 + 82.6 x 50.8mm
vixit1862
Just Starting Out
Just Starting Out
Posts: 3
Joined: Mon Nov 07, 2016 7:56 pm
Boat Name: No Boat Yet

Re: Welcome!

Post by vixit1862 » Wed Nov 09, 2016 2:47 pm

http://s1255.photobucket.com/user/vixit ... sort=1&o=3
http://s1255.photobucket.com/user/vixit ... sort=1&o=4
http://s1255.photobucket.com/user/vixit ... sort=1&o=1
Thank you for your replies. Most interesting. It looks like we have identified the engine. I hope that we have better shots of it this time.
As for the boiler, I believe it has been modified to comply with some French rule that restricts the capacity of the boiler. It was 30litres, and is now perhaps 20litres. It is a vertical boiler, as can be seen(?), and I believe that it may be of the constant water level type. Next time I'm looking at the boat, I'll try to establish what comes through the pipes, hot air or water.
Again, thank you all for your help. Lastly a poor picture of the boat. I'll do better next time!
http://s1255.photobucket.com/user/vixit ... sort=1&o=6
vixit1862
Just Starting Out
Just Starting Out
Posts: 3
Joined: Mon Nov 07, 2016 7:56 pm
Boat Name: No Boat Yet

Re: Welcome!

Post by vixit1862 » Wed Nov 09, 2016 2:53 pm

http://s1255.photobucket.com/user/vixit ... sort=1&o=6
I'll get the hang of this one day. Not particularly easy to use!!
User avatar
Akitene
Warming the Engine
Warming the Engine
Posts: 81
Joined: Wed Nov 18, 2009 7:39 pm
Boat Name: No Boat Yet
Location: Bordeaux, France

Re: Welcome!

Post by Akitene » Wed Nov 09, 2016 8:45 pm

Well, the mysterious engine is an Anthony Beaver Compound. Saddly, the links to your additionnal photos don't work.

Not very surprised about the story of this boiler. My understanding of the French regulation on using boilers is that it's limited to the compliance to the European Union rules, that is merely restricting the product pressure x volume below a certain value. Hence the diminished volume.
User avatar
PeteThePen1
Full Steam Ahead
Full Steam Ahead
Posts: 553
Joined: Thu Nov 19, 2009 11:53 pm
Location: Aberystwyth, Wales, Europe
Contact:

Re: Welcome!

Post by PeteThePen1 » Mon Nov 14, 2016 5:53 pm

Hi

Just a thought. If you are an SBA member, don't forget that we do have a service for members which can help them get boilers of uncertain origin certified. Basically you need to make a good drawing of the pressure vessel and any information that is on the boiler or in the boat documents about its origin. The engineering gurus of SBAS will then do their sums and come up with an assessment. If it gets an OK you can get it tested and things go from there.

Send a note to Kevin (Manor Farm Engineering) to enquire about getting the boiler assessed by SBAs. He is involved with SBAS so will have the details right. I picked up this information from gossip!

Regards

Pete

(Just been looking at your pics on Photobucket. I see the boat has a nice copper water separater in the steam line, so is presumably a puffer.)
Post Reply